ADS7884: Can this device operate in continuous mode ? (CS held low)
Part Number:ADS7884Will the ADS7884/7885 perform successive(continuous) conversion & output consecutive data words ? eg: if CS is held low. I have read datasheet section a number of times but...
View ArticleClik here to view.
DAC3171: Layout question
Part Number:DAC3171Hi,in my current design, I'm using DAC3171. I see some spurs when TX with the DAC when I checked my Layout I saw that there are some differences between what I did and what is shown...
View ArticleADS1110: questions of ADS1110 converting
Part Number:ADS1110hi, i have couple questions when using ADS1110 convertor.1. seems like there are no Sample & Hold funtion for this devices, so what happen if the intput voltage change when...
View ArticleADS8353: SAR ADC and driver circuit
Part Number:ADS8353In ti-precision-labs-adcs, there is an example to use the tool for R-C charge bucket values. the Rflt/2(4.1 ohm to 32.5 ohm) and Cflt(1.1nF) are based on the driver amplifier's gain...
View ArticleADS7947: ADS7947: reflow profile
Part Number:ADS7947please support the reflow profile of ADS7947:
View ArticleClik here to view.
ADC12D1800RF: ADC Spurious Seen during read SRAM
Part Number:ADC12D1800RFDear SirI had developed a board with TI ADC12D1800RFIUT, FPGA and ZBT Cypress SRAM. In the Hardware, Each ADC/SRAM is powered up by a separate LDO. While the FPGA VCCO/AUX Core...
View ArticleADC128S052: Qualification Summary of ADC128S052QCMT/NOPB
Part Number:ADC128S052Please support the Qualification Summary of ADC128S052QCMT/NOPB
View ArticleClik here to view.
ADC128S102: THD improvement
Part Number:ADC128S102Hi Team,Attached the circuit what we followed in our design. As per datasheet, THD value is -74dB. But I am getting -51dB only. Please suggest some solution to improve THD.Thanks...
View ArticleDDC232: DDC232/316 input protection
Part Number:DDC232Hi,We are using a DDC316 and DDC232 with two anti parallel diodes on the input as a protection of the device. In the past we used the PAD1/5/10 devices and switched to a mmbf4117...
View ArticleAMC1306E05: Are there any input limitations?
Part Number:AMC1306E05Hi team,I just want to confirm just in case.Is it OK that AINP is connected to GND like the attached, case 2?(Please visit the site to view this file)Regards,Noriyuki Takahashi
View ArticleCCS/LMP91000: How long is the LMP91000 exiting the DeepSleep mode output...
Part Number:LMP91000Tool/software: Code Composer StudioHello everyoneI found the following problems in the process of using LMP91000: I quit from the DeepSleep mode and enter the 3lead amperometric...
View ArticleADCS7476: ADCS7476 data run error
Part Number:ADCS7476Dear Experts,there have a question：“why when they open the buffer memory the data is from BIT0--BIT11，and close the buffer memory the data is from BIT1--BIT12？”hope you can give...
View ArticleADS8887: ADS8887 multiple data resister read
Part Number:ADS8887Hi team,Can we read the same data resister value of ADS8887 in multiple-times if we would not issue CONVST during multiple reading?Best regards,Iwata Etsuji
View ArticleClik here to view.
VSP1000: output of vsp1000 getting attenuated
Part Number:VSP1000I have apply 8V offset and 1V peak to peak of 1Mhz.But at output of vsp1000 getting half voltage that 0.5v peak to peak.I have attached the input,output waveform and schematic.
View ArticleDAC7760: I want A start model for the DAC7760 of the programming by spI
Part Number:DAC7760Hello, We have designed 4 DAC channels on board using DAC7760 by SPI. We use the STM32F series as our MCU.Best Regards,Beyond
View ArticleClik here to view.
TSW1400EVM: TSW1400EVM Module with ADC1173 Parallel AD Converter
Part Number:TSW1400EVMHello!For reading and analysis of high speed analog signals I have wanted to use the ADC1173 Board in combination with TSW1400EVM Evaluation Module. Since this is a parallel ADC...
View ArticleADC128S102QML-SP: ESD Rating
Part Number:ADC128S102QML-SPHi Team, I have a customer that needs the ESD Rating for ADC128S102QML-SPThank you in advance for your help
View ArticleADS1256: Bleedover/noise in differential readings between channels..
Part Number:ADS1256I am noticing bleed over when pulling differential data from channels.here is an output: where 0 is channel 0,1 channel 1 is 1,2 and so forth..Channel 0: 1.718778vChannel 1:...
View ArticleADS8668EVM-PDK: ADS8668EVM-PDK
Part Number:ADS8668EVM-PDKCan you share sdcc driver for windows10 64bit system.
View Article[FAQ] TSC: Touch Coordinates are Unstable
Hello,When I short press the touch screen I am getting unstable values but when I long press, the values are stable. What is wrong?Regards,Aaron
View Article
